RADIO FUTABA 9ZAP WORLD CHAMPION MODEL II
9-CANALES PCM



This is the World Champion Model II of the Futaba 9ZAP. This radio has programming for all types of aircraft - airplane, helicopter, or sailplane.

**The S indicates the Synthesized module and Synthesized receiver are incl***

THERE ARE NO SERVOS PACKAGED WITH THIS RADIO IN THE BOX.

****** THE POLY SWITCH BYPASS WILL NOT WORK WITH THIS TRANSMITTER. *****

The changes from the 9ZAP to ALL WC models (9ZAW, ZHW, ZHWS, ZAWII ZHWII): (NOTE: All other functions of the 9ZAP are still with this radio.)
- Rename of dials from VRA/VRB to Left and Right Dials for ease of use
- New fuel mixture control functions (FMC)
- New Gyro Sense Mixing Function for Gyros (501 and others)

The changes from the 9ZAW to the WC II radios are:
- four 3-position switches on the face;
- distinctive blue markings and ergonomic sticks;
- TX packaged without Receiver, servos, or MODULE
- 1100mAh transmitter battery and 1500mAh receiver battery
- Increased frame rate around center for digital servo response time (analog servos can not take advantage of this increased rate)
- TX case silkscreened to clearly identify the WC2.

Differences between 9ZAWII and 9ZHWII radios:
- The 9ZH defaults to helicopter models and has no throttle ratchet.
- The 9ZA defaults to aircraft models and has a throttle ratchet.

SYSTEM FEATURES:
* This is a 1024 PCM system, Futaba's highest resolution
* 10 model memory (this can be any type of model; airplane, heli or sailplane)
* 8-character model name for each of the 10 model presets
* An optional plug-in memory module (called a CamPac - FUTM9400) which increases the model memory 5 more to 15 models
* Up to 8 flight conditions for each model in memory
* 5 programmable mixers with special advanced functions for each model setup
* Each flight condition separately programmable
* Flight condition and channel delay setting
* Ergonomic shape - very easy to hold and operate
* Ball bearing control sticks * Switchable FM/PCM
* Adjustable tension, length, and angle on control sticks
* Programmable transmitter switches * Soft keys to make programing easy
* Large LCD (liquid crystal) display with contrast adjustment
* Unique Digital trim (2 rates) * Failsafe/hold setting
* Data copy functions * Swiveling transmitter antenna
* Low voltage alarm * Automatic system power off
* Electronic servo centering, reversing, throw volume, and exponential
* Special mixer alarm * A built-in tachometer in TX case
* A voltmeter with switchable loads for TX and RX batteries
* A trainer system
* Two separate timers and elapsed time counters
* A DSC (Direct Servo Control) system - you can move the servos by plugging the transmitter into the receiver and not transmitting over the radio wave (This is used in the "pits" where you want to operate your receiver without "shooting" someone down).
* Flexible frequency -- any 72 MHz channel with a simple programming change!

INCLUDES:
(1) Transmitter case (FUTM5701)
(1) 9ZA WCII Transmitter (no stock #) (1) DSC cord (FUTM4250)
(1) Rx NiCad R4F1500 (FUTM1285) (1) NT8S 1100mAh Tx NiCad (FUTM14700)
(1) H/D Receiver switch harness(FUTM4385) (1) DSC/Charge harness (FUTM42433)
(1) FBC19B(4) Charger for 1000mAh RX and 700mAh TX batteries (FUTM1830)
(1) Transmitter neckstrap (the wide one, not the thin one) (FUTM5692)
(1) 153 page instruction manual with 26 page instruction supplement
(1) Synthesized Module (FUTL8900) and Receiver (FUTL7600)

OPTIONAL EQUIPMENT:
Campac memory module (FUTM9400)
Trainer Cord (FUTM4410)
Channel Specific Module (FUTL17**) for use on a specified 72 MHz freq
Heavy Duty Gimbal Springs (FUTM3640) can be used in the 9Z, but it is STRONGLY recommended that the customer send this transmitter into the Futaba Service Center for this service per the complexity of the internal portions of this transmitter.

NOTE:
A 9Z*W can not be converted to WC2. The new radio has new parts from gimbals to mother boards and the cost to convert would be prohibitive.

This radio's TX NiCD pack can not be cycled unless a special jumper cable is used because the battery is in a protective case which includes the diode. To jump the diode for cycling purposes, the customer will need to special order HSP78050 through dealer.



volver a la página inicial - volver a radios


Links a fabricantes


























Helices y Motores
Av. 6 de Diciembre 5603 y Louvre, Centro Comercial Jr. Local No. 2 (junto a la Espe)
Telf: 02 224 9054 • Cel: 096 016 925
info@helicesymotores.net